Recent Posts

21

Bug reports / Re: New Scenario and Own Ship

« Last post by forum_admin on April 29, 2024, 10:21:47 PM »

Thanks. At the moment, to update the scenario with course or speed changes, you need to use the 'Change Leg' button for the 'Own Ship' settings, and either 'Change Leg' or 'Add Leg' button for other ships. In https://github.com/bridgecommand/bc/commit/0c2153d0a4794e1b3bbeaae038abea37e8fd5e51 I have changed this so for the 'Own Ship', the changes will take effect immediately. I have left it unchanged for 'Other Ships', because you may want to be adding a series of 'legs', and type in the values for the next leg.

I think the uninitialised value would depend on many things, as it depends on what happened to be in that memory location before. I have fixed this in https://github.com/bridgecommand/bc/commit/a536c8394efd79c1b06cfcfc23ed92c059b751de

I'm currently aiming to add a few updates to the VR interface, and will then put out an updated release.

22

Bug reports / Re: New Scenario and Own Ship

« Last post by rellufdarb on April 27, 2024, 07:59:37 AM »

Yes it does. Change the data field then hit Change Leg then hit Save and the appropriate ownship.ini file is modified accordingly. So the only real issue is the default value when the new scenario is created. I have checked briefly and the default decimal value of 6961384356225895000000000000000000.000000 doesn't seem to be a convenient binary (all 1's) or Hex (all F's) number so would be curious to discover where it comes from?

23

Bug reports / Re: New Scenario and Own Ship

« Last post by forum_admin on April 26, 2024, 10:06:13 PM »

Hi, thanks for pointing this out. I think that some of the data in the scenario editor may be uninitialised, which should be simple to fix.

If starting a new scenario, if you set the own ship speed and heading, then click 'Change leg', and save, does it work for you?

24

Bug reports / New Scenario and Own Ship

« Last post by rellufdarb on April 26, 2024, 05:08:21 AM »

If I open the Scenario Editor and Create a New Scenario, the Speed of Own Ship is a ridiculously large number (  InitialSpeed=6.96138e+33  ). The Course is 0.

When I change the speed to zero and save the scenario, it does NOT save the new speed. If I go to the ownship.ini file I can see the huge number. If I edit the ini file using notepad then save it is all OK. when I reopen the Editor----but still doesn't save any subsequent changes properly.

In fact, if I change the course to something other than 0.0, the scenario editor does not save that either. It does save a new position if I move ownship so the save function partially works.

Note, with this huge speed in the new scenario (before I discovered this issue),opening the Bridge Command gave very weird results--unsurprisingly !

25

Bridge Command General Support / Re: TerrainHeightMapSize

« Last post by forum_admin on April 23, 2024, 08:57:58 AM »

Hi, with a normal greyscale image, 0 represents -1*SeaMaxDepth, and 255 represents TerrainMaxHeight, with linear interpolation in between. This actually means that the 'half way' between max height and max depth is between 127 and 128 greyscale values.

I made a simple calculator at https://www.bridgecommand.co.uk/data/_uploaded/file/Height%20conversions_255.xlsx which might be useful.

The relatively small number of steps available in a greyscale image is why there is also the 'RGB' encoding (height in metres is set by (red * 256 + green + blue / 256) - 32768), or raw 32 bit floating point format available, which both allow a much finer elevation step.

26

Bridge Command General Support / Re: TerrainHeightMapSize

« Last post by rellufdarb on April 23, 2024, 12:18:16 AM »

Hello Admin,

OK, makes sense.

I am just starting with Bridge Command. So far I have been trying to use (simple) greyscale .png files for height. I am having difficulty getting realistic shorelines--getting the slope right is hard and I usually end up with cliffs because I have the greyscale gradient too steep. To manually edit a large map has consumed many hours late at night already.

One question, for an 8 bit 256 level greyscale, is zero (water level) represented by 127 or half way between Max Height and deepest depth in the terrain.ini file?

27

Models / Re: Outboard Motors

« Last post by rellufdarb on April 23, 2024, 12:13:26 AM »

There is obviously a lot of clever programming behind Bridge Command and I do have an electronics and programming background so I understand, but yes, I would think a "tweek" of azimuth drives would be one way to go. Just allow reverse thrust same as shaft drives but limit the rotation angles like rudders. The drives would have to be placed at the stern, but I see you already have parameters for the drive location.
In our case we have two outboard (on a rescue vessel) cross connected and steered from the one helm. I imagine both azimuth drives could be connected to the same joystick input so they turn together, just with separate throttle input for each.

28

Models / Re: Outboard Motors

« Last post by forum_admin on April 22, 2024, 10:25:17 PM »

Thanks for asking. I'll have a look into this, I think it would be relatively simple to change the way the azimuth drive is modelled to allow reverse propulsion direction as an option.

I think you could get the right turning effect from tuning the rudder parameters, but I'm not sure the lateral motion would be realistic.

29

Bridge Command General Support / Re: TerrainHeightMapSize

« Last post by forum_admin on April 22, 2024, 10:22:28 PM »

Hi, TerrainHeightMapSize is no longer required, so will now be ignored.

In earlier versions, it was previously required to specify the size of a square image defining the heightmap, but because this can be found directly from the image dimensions, it is not required any more.

If you are using a binary heightmap (a list of 32 bit floating point values), TerrainHeightMapRows and TerrainHeightMapColumns are now used instead, as non-square heightmaps are allowed.

30

Bridge Command General Support / TerrainHeightMapSize

« Last post by rellufdarb on April 22, 2024, 01:59:18 PM »

In the Terrain.ini files I see this-----TerrainHeightMapSize----but it is not listed in the relevant documentation. At least I cant find it.
Where is this defined please?